Accelerated Aging Testing: UV and Xenon Arc Methods for Plastics, Coatings, and Textiles

Accelerated Aging Testing: UV and Xenon Arc Methods for Plastics, Coatings, and Textiles

1. Accelerated weathering testing: fluorescent UV (ISO 4892-3, ASTM G154) vs xenon arc (ISO 4892-2, ASTM G155) Purpose. Accelerated weathering tries to compress months or years of outdoor exposure into days or weeks by intensifying sunlight-like UV, moisture (dew/condensation and spray/rain), and heat in a controlled chamber. It is a screening and comparative tool, not an exact outdoor prediction. - Fluorescent UV chambers: use UV lamps (commonly UVA-340 or UVB-313) to reproduce the damaging short-wavelength UV part of sunlight. They are strong for coatings, plastics, and composites where photooxidation, chalking, fading, embrittlement, and cracking dominate. - Xenon-arc chambers: use filtered xenon lamps to simulate full-spectrum sunlight (UV + visible + IR), including longer wavelengths. They are preferred for colour fastness, dyed textiles, inks, pigments, leather, and materials sensitive to visible light. Typical test modes (simplified): - UV condensation cycle: alternate UV “dry/hot” periods with condensation “wet/warm” periods, often without water spray. - Xenon weathering cycle: alternating light/irradiation with dark humidity or water-spray phases, often simulating daylight followed by cool dew formation. 2. Irradiance and cycle settings Key control variables you must fix before testing: - Irradiance level: the radiant power at a specified wavelength (e.g., W/m² at 340 nm for fluorescent UV; W/m²/nm or total radiant exposure in MJ/m² for xenon). Higher irradiance accelerates degradation but can change degradation mechanisms if too extreme. - Black standard / black panel temperature (BST/BPT): surface temperature under light. Important because oxidation, chalking, and fading are temperature-sensitive. - Chamber air temperature and relative humidity. - Wet/dry cycle: duration of UV vs condensation/sprays; pH and purity of water if spray is used. - Exposure duration: often specified as hours or total radiant energy; compared against real-world benchmarks from Florida or Arizona outdoor racks when available. Practical notes: - Always report lamp type, filter system, irradiance setpoint, temperatures, humidity, and cycle timing. Two “UV tests” can give very different results if cycles differ. - Keep reference samples of the same material unexposed to calculate retention. 3. Light fastness grading Light fastness is usually about how much colour change occurs after exposure. Two widely used scales: - Grey Scale for colour change (ISO 105-A03): grades from 1 to 5, where 5 = no visible change and 1 = severe change. Half-grades are common (4–5, 3–4, etc.). Used especially in textiles and coated materials. - Blue Wool Scale (ISO 105-B02): an 1–8 rating used mainly in textiles and pigments; higher numbers mean better resistance to light-induced fading. Instrumental colour measurement is often reported alongside visual grading: - Use a spectrophotometer to measure L*a*b* before and after exposure. - Calculate ΔE*ab (total colour difference) or dedicated indices such as CIEDE2000. - A common rule of thumb: ΔE around 1 is just noticeable to a trained observer; values above 3–5 are clearly visible. 4. Reading gloss, colour, and strength retention After exposure, compare exposed specimens to unexposed controls under the same preparation and measurement conditions. - Gloss retention: measure 60° (or 20°/85° according to surface type) gloss before and after exposure. Retention (%) = final gloss / initial gloss × 100. A drop indicates chalking, surface degradation, roughening, or loss of resin binder. - Colour change / colour retention: report both instrumental ΔE and visual grey-scale grade. “Colour retention” can be expressed as the remaining colour intensity, or simply as ΔE plus the fastness grade. - Mechanical strength retention: for plastics, coatings films, composites, rubber, or textiles, test tensile strength, elongation at break, impact resistance, flexural properties, or adhesion before and after exposure. Retention (%) = exposed property value / unexposed control value × 100. Example: 85% tensile retention after 1000 h UV means the material still keeps 85% of its original strength; 50% or lower often indicates severe embrittlement. Practical interpretation checklist: 1. Identify the dominant degradation mode: gloss loss, chalking, cracking, colour shift, embrittlement, or strength drop. 2. Compare against the relevant standard and customer acceptance limits, not against an arbitrary number. 3. Correlate accelerated results with real outdoor data if available; accelerated chambers are excellent for ranking formulations, but exact service-life prediction requires calibration.
2026/11/17
Reading volume: 1

News Details

A material that looks unchanged after a month indoors can fail within two summers outdoors. Weathering testing exists to find that out before a customer does, by reproducing sunlight, heat, moisture and rain in a laboratory chamber and measuring what the material loses.

The choice that shapes every later decision is the light source. Fluorescent UV lamps concentrate the short-wavelength part of sunlight that drives most polymer degradation; xenon arc lamps reproduce the full solar spectrum, including visible light, which matters whenever colour is part of the specification. Both are legitimate, and they answer different questions.

What Accelerated Weathering Testing Measures

Weathering is not a single property. A coating exposed outdoors changes in several ways at once, and a test programme has to decide which of them matter to the product.

  • Colour change. Measured as a colour difference value or graded on a grey scale; the primary criterion for textiles, decorative laminates and automotive trim.
  • Gloss loss and chalking. The first visible sign of coating breakdown, and usually the earliest measurable one.
  • Surface defects. Cracking, crazing, blistering, yellowing and haze on transparent parts.
  • Mechanical retention. The percentage of original tensile strength or elongation left after exposure, the standard way to express ageing of rubber, geotextiles and cable sheathing.
  • Adhesion and delamination. Whether a coating or laminate still holds to its substrate after moisture cycling.

A report that gives only one of these is incomplete for most specifications, because a material can hold its colour while losing half its elongation.

Why a Laboratory Test Replaces Outdoor Exposure

Outdoor exposure is the reference method, but it is slow and irreproducible: two sites at the same latitude receive different sunshine, rain and pollution loads, and a single test can take two years. Accelerated methods compress that into weeks by raising irradiance, temperature and moisture above natural levels, on the understanding that the ranking of materials is preserved even though the absolute time is not.

The consequence is that accelerated results are comparative, not predictive in calendar terms. Nobody can state that 500 hours in a chamber equals five years in a specific city. What can be stated is that material A lost more gloss than material B under an identical, documented cycle, and that is what a supplier qualification needs.

Fluorescent UV Methods: ISO 4892-3 and ASTM G154

The fluorescent UV apparatus holds a bank of lamps above a row of flat specimens, with a heated water pan below to produce condensation on the specimen face. It is the workhorse of polymer weathering because it delivers a high dose of the damaging UV band at modest cost, and it runs unattended for long cycles.

A chamber built on this principle, such as the ultraviolet accelerated weatherometer, combines UV radiation with condensation, spray, temperature and humidity in one enclosure: a working volume of 450 x 1170 x 500 mm, a temperature range from ambient plus 10 to 70 degrees C with a uniformity of plus or minus 3 degrees C, humidity at or above 95 percent RH during the condensation phase, six lamps spaced 65 to 70 mm apart at 50 mm from the specimens, and a programmable timing range of 0 to 999 hours. Irradiance, temperature and wetness are the three variables that decide the severity of any UV cycle.

UVA-340 and UVB-313 Lamps

Two lamp types dominate. UVA-340 has a spectrum that matches solar UV between 295 and 365 nm closely, which makes it the default for comparing against real outdoor exposure. UVB-313 emits below the solar cut-off and therefore ages materials faster, which suits quality control screening or specifications that deliberately accelerate. The two are not interchangeable: a result obtained with UVB-313 cannot be compared with one obtained with UVA-340, and the lamp type must be stated in every report.

Condensation, Spray and Dark Cycles

Dry UV alone does not reproduce outdoor failure. Most coatings fail because moisture penetrates and swells the film, then the next UV cycle breaks it down. Standard cycles therefore alternate an irradiation period at elevated black-panel temperature with a condensation period in the dark, typically 60 degrees C light and 50 degrees C condensation, with four-hour steps. Water spray is added where rain, thermal shock or acid rain resistance is relevant, and the spray water must be deionised, since hardness deposits create their own artefacts.

Xenon Arc Methods: ISO 4892-2 and ASTM G155

The xenon arc lamp is the closest laboratory approximation of full-spectrum sunlight. Because it emits visible and infrared radiation as well as UV, it reproduces both photochemical degradation and the heating that comes with sunlight, which is why it is the reference light source for colour fastness, automotive interior and exterior trim, and printing inks.

A water-cooled xenon arc weathering tester of the type used for textiles and leather illustrates what the method demands in practice: a 4500 W water-cooled long arc lamp with a rated life of 1500 hours, closed-loop irradiance control with an automatic compensation system, chamber temperature from 25 to 80 degrees C, black-panel temperature up to 120 degrees C and black-standard temperature up to 130 degrees C, humidity adjustable from 10 to 85 percent RH in the light cycle and up to 98 percent RH in the dark cycle, and a rotating rack at 1 to 4 revolutions per minute carrying up to 27 specimens in ISO holders or 18 in AATCC holders. Air-cooled xenon systems are cheaper to install but hold fewer specimens and control temperature less tightly.

Filter choice is the hidden variable in xenon testing. Daylight filters, window glass filters and extended UV filters each shift the spectrum, and a result produced behind window glass is not comparable with one produced under daylight filters, even at identical irradiance.

Choosing Between UV and Xenon Arc

The table below summarises the practical differences, which in most laboratories reduce to a single question: is the failure mode primarily chemical degradation, or does appearance matter?

Aspect Fluorescent UV Xenon arc
Spectrum UV band only Full solar spectrum with filters
Typical methods ISO 4892-3, ASTM G154, ASTM D4329 ISO 4892-2, ASTM G155, ASTM D2565
Best for Plastics, coatings, sealants, roofing, screening Colour fastness, textiles, automotive, inks, leather
Control variable Irradiance at 340 nm, black-panel temperature Irradiance at 340 or 420 nm, BPT or BST, humidity
Cycle time Usually hours to a few days Typically 250 to 1000 hours and beyond

Colour Fastness to Light in Textiles

For dyed textiles the question is narrower: how much does the shade change? ISO 105-B02 assesses this under xenon arc light against blue wool references graded 1 to 8, where grade 8 is the most lightfast. AATCC TM16 uses the same scale with an AATCC blue wool series and its own exposure options, and the two are not directly interchangeable because the exposure conditions differ.

Two details cause most disputes. The blue wool reference set used must be stated, because the two permitted sets under ISO 105-B02 do not fade identically. And light fastness is graded on the 1 to 8 scale, not the 1 to 5 grey scale used for washing and rubbing, so a buyer comparing the two numbers is comparing different scales. Where humidity matters, the light-and-perspiration combination is tested separately.

Specimen Preparation and Cycle Programming

Accelerated ageing magnifies preparation errors. A few rules keep results defensible.

  • Expose specimens of identical thickness and surface finish; a moulded skin and a machined face weather at different rates.
  • Mask part of each specimen or retain an unexposed control, so colour and gloss measurements have a reference.
  • Mount flexible materials on the specified backing; unsupported fabric and foam behave differently from backed specimens.
  • Keep the chamber loaded to its rated specimen capacity, because an empty chamber reaches temperature faster and shifts the effective dose.
  • Record the total radiant exposure, not only the elapsed hours, since lamp ageing and irradiance drift change the dose delivered.

Reading the Result: Gloss, Colour and Retained Strength

Colour difference and grey scale

Instrumental colour difference combines lightness, chroma and hue shifts into one number, which is convenient for specifications but hides direction. Reporting the components alongside the total tells a formulator whether a shade darkened, bleached or shifted hue, and therefore which pigment or stabiliser is at fault. Visual grading against grey scales remains the contractual method for textiles.

Gloss and chalking

Gloss is measured at a fixed geometry before and after exposure and reported as a percentage of the initial value. Chalking is assessed by tape or by wiping, and indicates that the binder has degraded at the surface rather than in the bulk.

Mechanical retention

For rubber, geotextiles and wire insulation, the meaningful result is retained tensile strength or elongation measured to the same standard as the unaged material. A 50 percent loss of elongation after exposure is a common acceptance limit, and it is invisible in a colour measurement.

Six Reasons a Weathering Result Cannot Be Reproduced

  1. Aged lamps. Output falls gradually and the spectrum drifts; lamp hours must be logged and lamps replaced on schedule, not on failure.
  2. Uncalibrated irradiance. A sensor that reads low causes the controller to overdrive the lamps, raising the real dose.
  3. Water quality. Tap water leaves scale on specimens and optics, altering both wetting and transmission.
  4. Chamber loading. Different specimen counts and backing panels change airflow and temperature distribution.
  5. Unstated filters. A xenon result without the filter type is not a result.
  6. Mixed lamp types. Replacing part of a lamp bank with a different type produces a spectrum nobody can reproduce.

Specifying a Weathering Test Chamber

A purchase specification should start from the standards the laboratory must serve, then work backwards to lamp type, irradiance range and control sensors. Confirm the specimen capacity against the largest batch you expect, the availability of the lamps and filters locally, the calibration route for the irradiance sensor, and whether humidity control is needed at all, since many UV methods specify condensation rather than controlled RH.

Weathering rarely stands alone in a laboratory. Photodegradation is usually confirmed by thermal ageing, humidity cycling and salt spray, and those instruments sit together in the environmental range, including the climate chamber group that covers constant temperature and humidity chambers, ozone chambers and thermostatic ovens. Buying the light source and the humidity source as one planned bench, rather than as separate purchases, avoids the common situation where a material passes 1000 hours of UV and fails its first humid heat cycle.

Share to:
facebook
line
Whatsapp
Pinterest
Tumblr
Linkedin
Color Fastness in Textiles: Testing Methods, Standards, and Equipment