Flammability Testing of Plastics and Electrical Components: UL 94, Glow Wire and Needle Flame

Flammability Testing of Plastics and Electrical Components: UL 94, Glow Wire and Needle Flame

How flammability testing works for plastics and electrical parts: horizontal and vertical bar tests, UL 94 ratings, glow wire indices, needle flame method, conditioning requirements and the errors that make results incomparable.
2026/11/19
Reading volume: 0

News Details

Flammability testing answers a narrow question with wide consequences: once a material is ignited by a defined source, does the flame stay, does it spread, does it drip, and does it go out by itself? Electrical enclosures, appliance housings, cable ducts and automotive interiors are all specified against that behaviour, and the tests that establish it are among the most standardised in the laboratory.

Three ignition scenarios cover most of the work. A small flame applied to a horizontal or vertical bar establishes how a plastic behaves when a nearby component burns. A electrically heated wire establishes whether a hot element or a loose connection can ignite the material. A needle flame establishes what happens when a tiny flame from a fault inside an enclosure touches a part.

What Flammability Testing Establishes, and What It Does Not

A flammability result describes the response of a small specimen to a defined ignition source under defined conditions. It is a material classification, not a statement that a finished product is fire safe. The same plastic can carry a V-0 rating at one thickness and fail at another, because thin sections conduct heat away less effectively and melt before they can self-extinguish.

Thickness, colour, flame-retardant loading, and even the direction of moulding flow all influence the result, which is why a rating is always quoted together with the specimen thickness at which it was obtained. A datasheet that says V-0 without a thickness is unusable in a design review.

Horizontal and Vertical Bar Tests

The bar test is the foundation of plastic flammability classification. A rectangular specimen is clamped at one end and a specified flame is applied to the free end, either horizontally, where the question is how fast the flame travels, or vertically, where the question is whether the flame goes out and whether burning material drips onto a cotton pad below.

The apparatus has to hold three variables constant: the flame size, the distance and angle of application, and the duration of contact. A horizontal and vertical flammability tester covers those requirements with adjustable inclination at 0, 20 and 45 degrees, a flame height set anywhere from 20 to 175 mm, a burner contact time programmable from 1 to 999.9 seconds, ignition repeatable up to 9999 times, a K-type thermocouple for flame calibration, a test space of 0.7 cubic metres with extraction, and an operating range up to 1050 degrees C. The tilting specimen holder matters more than it appears: the 45-degree position is used for the automotive and textile variants of the test, and a fixture that cannot be set accurately at each angle makes those methods unrepeatable.

UL 94 Ratings and What They Mean

The UL 94 classification is the one most often written into purchase specifications, and it is graded rather than pass or fail. The table below summarises the ratings a supplier is most likely to be asked to meet.

Rating Orientation Afterflame behaviour Dripping
HB Horizontal Burn rate below 40 mm/min over a 75 mm span, or flame out before 100 mm Not assessed
V-2 Vertical Up to 30 s per specimen, 250 s total for five specimens Permitted, may ignite the cotton
V-1 Vertical Up to 30 s per specimen, 250 s total for five specimens Not permitted
V-0 Vertical Up to 10 s per specimen, 50 s total for five specimens Not permitted
5VA / 5VB Vertical, 500 W flame Up to 60 s per specimen after five applications 5VA no hole through the plaque, 5VB hole permitted

Two practical points follow. First, V-2 is not weaker than V-1 in flame spread; the difference is that V-2 tolerates dripping that ignites cotton. Second, the test uses two sets of five specimens, with the flame applied twice to each in the vertical orientation, so ten specimens plus conditioning time are needed for a single evaluation.

Glow Wire Testing for Electrical Components

Glow wire testing simulates a different failure mode: an overheated element, a poor contact or a glowing connection raising a local surface above the ignition temperature of the plastic. A loop of nickel-chromium wire is electrically heated to a set temperature and pressed against the specimen with a defined force for a defined time.

A glow wire tester holds those conditions tightly: a 4 mm Ni/Cr 80/20 loop, a temperature range from 500 to 1000 degrees C, a contact force of 1.0 N with a maximum penetration of 7 mm, a specimen approach speed of 10 to 25 mm per second, a test space of 0.5 cubic metres, background illumination below 20 lux, and timed application from 1 to 999.9 seconds. The low background illumination is not a comfort feature; assessing whether a flame persists or a tissue layer ignites requires a dark enclosure, and a bright room makes the observation unreliable.

Three derived values are quoted in specifications, and they are routinely confused. The glow wire flammability index is the highest temperature at which the specimen extinguishes within 30 seconds of wire removal without igniting the tissue paper beneath it. The glow wire ignition temperature is the highest temperature at which sustained ignition does not occur during a 30-second application. The end product test applies the same principle to a finished part rather than a plaque. A specification that simply asks for glow wire compliance without naming which of the three is meaningless.

Needle Flame and Small Flame Tests

The needle flame test applies a small premixed gas flame, roughly the size of a match flame, to a part inside an enclosure for a defined period. It is used where the likely ignition source is a small flame from a fault rather than a hot surface, and it is frequently specified together with glow wire for the same component, because the two cover different scenarios.

For films and thin sections the horizontal small flame test is often preferred over the bar test, since a thin film cannot be clamped in the same way and tends to shrink away from the flame.

Conditioning and Laboratory Conditions

Flammability results are sensitive to moisture and to the test room itself.

  • Condition specimens at 23 degrees C and 50 percent relative humidity for at least 48 hours before testing; a damp specimen can behave differently from a dry one.
  • Run the test in a draught-free enclosure; air movement bends the flame and changes the burn rate.
  • Calibrate the flame height and, for glow wire, verify the indicated temperature with a separate thermocouple before each session.
  • Record the specimen thickness, colour and any anisotropy; a result is only valid at the thickness tested.
  • Renew the cotton pad for each specimen and keep it dry, since its ability to be ignited is part of the pass criterion.

Textile and Automotive Interior Variants

Textiles and interior trim use the same horizontal principle with different acceptance criteria. FMVSS 302, the standard applied to vehicle interiors, measures the burn rate of a horizontally held specimen and sets a limit of 102 mm per minute; a material that burns faster fails regardless of whether the flame self-extinguishes. The 45-degree variants used for some automotive and apparel specifications exist because the drape and orientation of a fabric change how a flame spreads across it.

Six Reasons Flammability Results Are Not Comparable

  1. Different thickness. The most common cause; ratings do not transfer between wall thicknesses.
  2. Flame calibration drift. A flame that is 5 mm too tall changes the afterflame time.
  3. Chamber draught. Extraction running too hard disturbs the flame.
  4. Conditioning omitted. Specimens taken straight from a humid store.
  5. Cotton pad condition. Damp or reused cotton fails to ignite when it should.
  6. Unstated standard edition. UL 94, IEC 60695-11-10 and ISO 1210 differ in detail, so a report must name the edition used.

Specifying Flammability Equipment

Decide first which standards the laboratory must serve, then check that the burner, the gas supply, the specimen fixtures and the extraction are matched to them. Confirm that the fixture can be set at every angle the methods require, that the chamber volume and extraction rate satisfy the standard rather than merely removing smoke, and that calibration accessories such as thermocouples and flow meters are supplied with traceable certificates.

Flammability results are also read alongside mechanical and thermal data, because a flame-retardant additive that raises a rating often costs impact strength or melt flow. Laboratories that qualify a compound usually run the burning tests together with the mechanical instruments in the plastic testing equipment range, so that a formulation change is assessed on both counts before it reaches a customer.

Share to:
facebook
line
Whatsapp
Pinterest
Tumblr
Linkedin