Rubber Ozone Aging Testing: Chamber Methods, Standards and Crack Analysis
News Details
Ozone is present in the air at concentrations measured in parts per hundred million, and it is enough to destroy a rubber part that is under tension. A gasket, a coolant hose or a door seal that performs perfectly in the laboratory can develop a network of fine cracks after a summer in a city, and the cause is not heat or sunlight but the reaction between ozone and the unsaturated bonds in the rubber.
Ozone aging testing exists because the failure is invisible until it happens. A specimen that shows no change after 24 hours can be heavily cracked after 96, and the difference between a compound that survives and one that does not is often a single additive.
Why Ozone Cracks Rubber
Ozone attacks the carbon-carbon double bonds that remain in the polymer backbone after vulcanisation. Natural rubber, styrene-butadiene rubber and nitrile rubber all contain them, which is why they are vulnerable; ethylene-propylene-diene rubber and silicone have saturated or differently unsaturated backbones and resist ozone far better.
The reaction is a surface phenomenon. Ozone cleaves the double bond and breaks the polymer chain at the surface, producing a thin brittle film. If the rubber is unstressed, that film simply sits there and the part looks intact. If the rubber is stretched, the film cannot follow the strain, so it ruptures, exposing fresh material to further attack, and the process repeats. The result is the familiar pattern of cracks running perpendicular to the direction of strain.
This explains why ozone cracking is a design problem as much as a compound problem. Any component installed under permanent tension or bending, from a stretched seal to a hose clamped over a pipe, carries stored strain energy that drives crack growth.
Static Versus Dynamic Strain
Two test modes cover the two ways a rubber part is loaded in service, and they produce different results on the same compound. Static testing holds the specimen at a fixed elongation for the whole exposure; dynamic testing cycles the strain, which repeatedly ruptures the protective surface film and generally accelerates crack formation.
| Aspect | Static strain | Dynamic strain |
|---|---|---|
| Specimen loading | Held at fixed elongation in a frame | Cycled between two elongations on a moving rack |
| Typical strain | 20% elongation is the common default, with 5 to 45% also used | Lower and upper limits set by the method, often 0 to 25% |
| Where it applies | Seals, gaskets, stored parts, clamped hose ends | Belts, diaphragms, suspension parts, weatherstrip |
| Typical standard | ISO 1431-1, GB/T 7762 | ISO 1431-2 |
| Failure usually seen | Few deep cracks at high-strain regions | Dense, shallow cracking over the whole gauge |
A compound that passes static testing can fail dynamically, so the specification must name the mode. Reporting a static result as evidence for a dynamic application is one of the most common errors in rubber qualification.
What an Ozone Test Chamber Has to Control
An ozone chamber is a temperature-controlled, light-tight enclosure in which specimens are held under strain in a moving air stream containing a known ozone concentration. Light exclusion matters: ultraviolet light generates its own degradation and would confound the result.
An ozone test chamber built for these methods shows the variables that have to be held steady. The HY3720 series is offered in two configurations, the A model with static specimen frames and the B model with a dynamic rack, over a working chamber of 500 x 500 x 600 mm. Ozone concentration is adjustable from 10 to 1000 pphm with a deviation within 10 percent, temperature from ambient plus 10 to 50 degrees C with a fluctuation of 0.5 degrees C and a uniformity of 2 degrees C, timing up to 999 hours, airflow from 2 to 25 L/min, and a specimen rack rotating at 1 to 17 revolutions per minute on the dynamic model.
Each of those numbers changes the severity of the test. Airflow is the one most often neglected: ozone is consumed at the specimen surface, so a chamber with poor circulation develops a concentration gradient and specimens at the back of the rack see less ozone than the record states.
Concentration, Temperature and Humidity
Ozone concentration is normally reported in pphm, where 100 pphm equals one part per million. Standard test programmes commonly use 25, 50, 100 or 200 pphm, and the choice should reflect the environment the part will see: a sealed interior application and an outdoor installation in a polluted city do not warrant the same severity.
Temperature has a double effect. The reaction rate rises with temperature, but so does the mobility of protective waxes and antiozonants, which bloom to the surface faster. A compound that passes at 23 degrees C may therefore fail at 40 degrees C, not because the chemistry changed but because the protective layer softened or was mechanically removed.
Humidity is usually left uncontrolled or held at a moderate level, and it affects results far less than concentration, strain and temperature. Where a specification includes it, it should be recorded, because condensation on a cold specimen can shelter the surface from ozone.
Standards: ISO 1431, ASTM D1149 and GB/T 7762
ISO 1431 is published in parts, with part 1 covering static strain and part 2 dynamic strain. GB/T 7762 is the Chinese equivalent for static testing and is widely cited in domestic supply chains, while ASTM D1149 covers rubber deterioration in an ozone chamber under both static and dynamic conditions.
The parts that matter in practice are the ones suppliers omit: the ozone concentration, the strain level, the exposure duration and the assessment interval. Two reports both citing ISO 1431 can describe tests 30 pphm apart at different strains, which is enough to reverse the ranking of two compounds.
Reading a Crack Assessment
Ozone results are reported by describing cracks rather than by a single number, usually combining a count or density with a size, for example few and small, or dense and deep. Some specifications require the time to first visible crack at a stated strain, which is a more useful engineering number than a pass or fail after a fixed exposure.
Photographs taken under the same magnification and lighting are the only reliable way to compare results between laboratories and over time. A description such as slight cracking means different things to different observers, and the discrepancy usually surfaces only when a customer rejects a batch.
Why Some Compounds Survive and Others Do Not
Ozone resistance is built into the formulation, not added at the end.
- Antiozonants. Chemical antiozonants migrate to the surface and compete with the double bonds for ozone; their effect depends on concentration, solubility and time, so a freshly moulded part may behave differently from one aged in storage.
- Waxes. Paraffin and microcrystalline waxes form a physical barrier. They work well in static applications and poorly under dynamic strain, where the film is continuously cracked open.
- Polymer choice. EPDM, silicone, fluoroelastomer and hydrogenated nitrile resist ozone chemically; natural rubber and SBR depend almost entirely on additives.
- Cure state and filler loading. Under-cured compounds have more available double bonds, and high filler loading introduces surface defects that act as crack initiators.
Six Reasons an Ozone Result Cannot Be Reproduced
- Uncalibrated ozone generation or sensing. The analyser drifts and the true concentration departs from the setpoint.
- Poor airflow distribution. Specimens at different rack positions receive different doses.
- Light leakage. Daylight or room lighting reaching the chamber adds photo-oxidation.
- Inconsistent strain. Specimen thickness varies, so the same jaw separation produces different elongation.
- Storage history. A specimen tested weeks after moulding has already lost or bloomed its protective additives.
- Observer variation. Crack grading without a documented scale and photographs.
Specifying and Using an Ozone Chamber
Start from the standard and the strain mode, then confirm that the chamber covers the concentration and temperature range with an analyser that can be calibrated on site, and that the rack geometry matches the specimen frames you intend to use. Confirm the chamber volume against the number of specimens a routine batch requires, and check that the door seals and exhaust are designed for ozone service rather than adapted from a general purpose oven.
Ozone aging is one of a group of environmental tests that together describe how a rubber part ages, alongside heat aging, humid heat and light exposure. Laboratories building that capability usually group the ozone chamber with the constant temperature and humidity equipment in the climate chamber range, and with the physical test instruments that measure what the ageing has done to strength and elongation, grouped under rubber and plastic testing equipment.
The practical lesson from field failures is consistent: ozone cracking is not a random material defect. It is a predictable consequence of strain, concentration and additive system, and a chamber test that records all three can tell a compounder which of them to change.